Before an industrial thermal fluid heater enters formal commissioning following mechanical installation, plant engineers must organize a multidisciplinary commissioning team, verify all technical documentation, and complete a full internal and external inspection across the heater unit, hot oil system piping, combustion auxiliaries, and instrumentation controls.
Commissioning Team Organization and Operator Qualifications
Commissioning must be carried out collaboratively by engineering and technical specialists, equipment managers, operators, maintenance technicians, safety engineers, quality inspectors, and construction trades—including electricians, instrument technicians, boilermakers, welders, and pipefitters. A dedicated commissioning leadership team must be established to formulate the commissioning plan and step-by-step procedures under unified command, defining clear responsibilities for every participant so that any abnormality is reported and resolved immediately.
Operators and boiler attendants must complete professional technical training, pass qualification examinations, and hold valid operating certificates before taking duty. Prior to startup, operators must thoroughly review the hot oil heater technical manuals and applicable technical regulations, understand the process system’s operating principles, and master proper operating procedures.
Technical Documentation Review and Verification
Prior to physical system checks, verify that all technical documents for the thermal oil heater and its associated process equipment are complete, including product qualification certificates, quality certificates, engineering calculation sheets, and operation and maintenance manuals. Confirm that installation quality and hydrostatic/pressure-test acceptance reports for the hot oil boiler and all process piping comply with applicable engineering standards.
30-Point Equipment and Process System Inspection Checklist
- Commissioning may begin only after all equipment installation, positioning, and construction acceptance work is complete. Qualified technicians must conduct a comprehensive internal and external inspection of the main heater unit, auxiliary equipment, accessories, heat supply system, heat-consuming system, combustion system, electrical and instrumentation control system, piping, and valves to verify both product quality and installation quality prior to use.
- Verify that the layout of all equipment and process systems is properly arranged and that the expansion tank installation elevation provides sufficient static head.
- Verify that the flow cross-section of the main thermal oil circulation line is adequate, and confirm that all piping and accessories are leak-free with tight welds and sealing joints.
- Verify that the slope, length, elbow configuration, flow cross-section, and routing of the expansion pipe are properly designed and installed.
- Verify that the bypass control valve is positioned for convenient operator access and adjustment.
- Verify that all blowdown valves, air vent valves, and drain/relief vent valves are properly installed.
- Verify that the heat transfer medium flow cross-section across all heat-consuming equipment is sufficient.
- Verify that the flow cross-section and height of the flue duct and chimney are properly sized.
- Verify that each valve’s model, size, temperature rating, pressure rating, structural type, and packing/gasket material meet specifications, and confirm smooth, reliable operation with accurate open/close position indicators.
- Verify that supports and hangers for all process pipelines, air ducts, and flue ducts are secure and rigid, ensuring that structural loads are not borne by the heater or auxiliary equipment.
- Verify that all pipelines have adequate thermal expansion allowance.
- Verify that the emergency replacement valve is properly installed and readily accessible for operation.
- Verify that the oil-gas separator is properly positioned and piped.
- Verify that all system strainers and filters have been thoroughly cleaned.
- Verify that all temporary process blind plates used during pressure testing have been removed.
- Verify that the thermal insulation materials and insulation thickness throughout the hot oil system meet project specifications.
- Verify that the seal between the heater body and the grate combustion chamber is tight.
- Verify that the under-grate air plenum chambers are tightly sealed.
- Verify that the forced-draft fan damper is properly installed and that the impeller rotates freely without binding.
- Verify that the induced-draft fan drive belt tension is properly adjusted and that the impeller rotates freely without binding.
- Verify that the inlet and outlet passages of the oil-charging pump are unobstructed and free of any blind plates.
- Verify that the coal feeder limit switches are properly installed and functional.
- Verify that the dust collector cover plates are tightly sealed.
- Verify that the slag extractor water seal is properly connected.
- Verify that the grate tension is properly adjusted.
- Verify that the concentricity and coaxiality of the grate speed-reducer main shaft and the operation of the safety clutch meet technical requirements.
- Verify that the hot oil circulating pump anchor bolts are securely tightened and that the pump shaft concentricity and coaxiality meet alignment tolerances.
- Verify that the electrical control panel layout complies with requirements for convenient operation and maintenance, with accurate electrical and instrument wiring and responsive pushbuttons.
- Verify that all temperature, pressure, differential pressure, liquid level, and flow instruments, sensing elements, transmitters, and actuators are complete and properly installed.
- Inspect, drain, clean, and purge all residual water and foreign debris from inside all piping and equipment.